View TX06D15VM1EAA_2919655.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

no. 3284ltd-1468-5 liq u id cr ystal displa y mod ule tec hn ical data TX06D15VM1EAA (note) 1. this docu ment may, w holly or partially, be subject to change w ithout notice. 2. all rights are reserved ; no one is permitted to reproduce or duplicate, in any fro m, the w hole or part o f this docu ment w ithout hitachi's permission. 3. no one is per mitted to explain contents of this docu ment to third parties w ithout hitachi's per mi ssion. 4. hitachi w ill not be held responsible for any da mage to the user that ma y result fro m a cc idents or any other reasons during operation o f the user's unit according to this docu ment, any previous reports or oral discussions. 5. circuitry and other examples described herein are meant merely to indicate the characteristics and perfor mance o f hitachi's products. hitachi assu me s no responsibility for any intellectual property c laim s or other problems that ma y result fro m applications based on the exa mple s described herein. 6. no license is granted by implication or other w ise under any patents or other rights o f any third party or hitachi, ltd. 7. l ife support a pp l ic ations : hitachi's products are not authorized for use in l ife support systems. t en tative www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 3. general data (1) part name (2) module dimensions (3) active area dimensions (4) pixel pitch (5) resolution (6) color pixel arrangement (7) display mode (8) color number (9) viewing direction (10) back light (11) weight (12) power supply voltage (13) lcd driver ic (14) interface TX06D15VM1EAA 41.85(w) mm x 56.0(h) mm x 4.6(t) mm 34.848(w) mm x 43.56(h) mm 0.198(w) mm x 0.198(h) mm 176 x 3 (r,g,b)(w) x 220 (h) dots rgb vertical stripe transflective type, normally black mode 65k or 262k colors 6 o'clock light emitting diode (led) 13.8g (typ) vcc=vci= 2.8v (typ) source ic : hd66772 gate and power ic : hd66774s clock synchronized serial interface (spi) + rgb interface (18bit) 16bit rgb - i/f 65k colors (use 16bit of the 18bit bus interface) 18bit rgb - i/f 262k colors 3284ps 2603-TX06D15VM1EAA-4 3 -1/1 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 4. absolute maximum ratings 4. 1 electrical absolute maximum ratings of lcd note 1 voltage from gnd. note 2 applies to the reset, id, sdo, sdi, scl, cs*, vld, vsync, hsync, dotclk enable, and pd17-0 pins. note 3 ambient temperature vs. allowable forward current 4. 2 environmental absolute maximum ratings note 1 ta < 40 deg c : 85%rh max. ta>40 deg c : absolute humidity must be lower than the humidity of 85%rh at 40 deg c. note 2 background color changes slightly depending on ambient temperature. this phenomenon is reversible. item ambient temperature humidity corrosive gas operating min -20 deg c note 1 not acceptable max 70 deg c storage min -30 deg c note 1 not acceptable max 80 deg c comment note 2 without condensation note 4 150pf-1.5kohm/200pf-0 ohm, 25 deg c-70%rh. the surface of lcd center are subjected. ambient temperature (deg c) 30 20 10 0 0 20 40 60 80 100 6ma(85 deg c) vss=0v item power supply for logic input voltage input current led reverse voltage symbol vcc vi i i v r min -0.3 -0.3 0 - max 4.6 vcc+0.3 100 5 unit v v ma v comment note 1, 2 power supply for analog vci -0.3 4.6 v led forward current i led - note 3 ma static electricity - - (+/-2) kv note 4 note 1 note 1 3284ps 2604-TX06D15VM1EAA-4 4 -1/1 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 3284ps 2605-TX06D15VM1EAA-4 5 -1/1 ta=25 deg c, vss=0v note 3), 5) 4), 5) tft-lcd module item logic vcc vi icc + ici f flm - "h" level "l" level all white - input voltage for logic circuits power supply current frame frequency symbol condition min typ max unit 2.72 0.7xvcc -0.3 - - 2.8 - - 90 2.89 vcc 0.15xvcc - v v ua hz - partial analog vci - 2.72 2.8 2.89 standby v led - led forward voltage - 3.6 - v i led - led forward current - 15.0 ma - - - - 650 3 2000 power supply voltage output voltage for logic circuits "h" level "l" level 0.75xvcc - - - - 0.15xvcc v vo (note 9) 1) 1) 2) 6) ua input/output leak current i li - -1 1 - sleep moving picture(full) - - - - 40 (10.3) ma 7) 8) 5. electrical characteristics (note 5) still picture is internal ram. (note 6) vcc=vci=2.8v, sleep mode & no rgb i/f input signals. (note 7) vcc=vci=2.8v, standby mode & no rgb i/f input signals. (note 8) vcc=vci=2.8v, 18bit- rgb i/f & high speed write mode. (fflm=90hz, black & white checker) all data written via the rgb-i/f are written to the internal ram. (note 9) refer to the 4. 1 electrical absolute maximum ratings of lcd.(page 4-1/1) (note 1) reset, id, sdo, sdi, scl, cs*, vld, vsync, hsync, dotclk, enable, pd17-0 (note 2) excepted the current of out driving mos. (note 3) vcc=vci=2.8v, internal clock operation mode & no rgb i/f input signals. (note 4) vcc=vci=2.8v, 8 colors mode, f flm =45hz, no rgb i/f input signals. pins: reset, cs*, scl, vld, id vsync, hsync, dotclk enable, pd17-0 pmos nmos vcc gnd pins: sdo, sdi nmos pmos vcc vcc pmos nmos (output circuit : three state) output data output enable gnd (input circuit) gnd 16 line : white (8 color mode) 204 line : black (8 color mode) partial pattern www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 6.1 optical characteristics of lcd (backlight on) 6. optical characteristics (measurement condition : hitachi standard) ta=25 deg c item viewing angle brightness response time (rise+fall) symbol f2-f1 k b tr+tf condition q=0 deg, k > 2.0 f=0 deg, q=0 deg min 50 - - typ 60 60 max - - - unit deg - cd/m2 ms note 4),6),7) 6) 8) contrast ratio f=0 deg, q=0 deg f=0 deg q=0 deg q=90 deg, k > 2.0 40 - - 70 color tone (primary color) x y red x y x y x y green blue white 0.52 0.33 0.32 0.49 0.15 0.14 0.29 0.31 - 9) 30 35 uniformity - f=0 deg, q=0 deg - - +/-30 % 3),5) ta=25 - 280 140 0.47 0.28 0.27 0.44 0.10 0.09 0.24 0.26 0.57 0.38 0.37 0.54 0.20 0.19 0.34 0.36 60 deg c ta=0 deg c f=0 deg q=0 deg 1) 3284ps 2606-TX06D15VM1EAA-4 6 -1/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 note 2. definition of reflectance "r" circular and flat light source sensor circular hole lcm or swb 6.2 optical characteristics of lcd (backlight off) ta=25 deg c item (measurement condition : hitachi standard) viewing angle reflectance response time (rise+fall) symbol f2-f1 k r tr+tf condition q=0 deg, k > 2.0 min 15 - - - typ 20 60 60 50 max - - - 25 unit deg % ms note 2) 4),6) 6) 8) contrast ratio f=0 deg, q=0 deg q=90 deg, k > 2.0 15 - color tone (primary color) x y red x y x y x y green blue white f=0 deg q=0 deg 0.49 0.34 0.35 0.44 0.20 0.17 0.38 0.36 - 9),10) (b/l:turned off) 5 f=0 deg, q=0 deg - 200 100 0.44 0.29 0.30 0.39 0.15 0.12 0.33 0.31 0.54 0.39 0.40 0.49 0.25 0.22 0.43 0.41 - f=0 deg q=0 deg ta=25 deg c ta=0 deg c note 1. definition of brightness "b" sensor : topcon/bm-5a or same level equipment measuring point : active area center 500mm 500mm sensor lcm blcm : brightness of lcm at optimum voltage. (displaying white pattern) bswb : brightness of swb. swb : standard white board. blcm bswb r = x 100(%) 3284ps 2606-TX06D15VM1EAA-4 6 -2/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 3284ps 2606-TX06D15VM1EAA-4 6 -3/3 note 4. definition of q and f (normal) viewing direction x y (q=180deg) y' (q=0deg) x' z f1 f2 q k = brightness when displaying black raster brightness when displaying white raster note 6. definition of contrast "k" note 5. definition of the brightness uniformity (average brightness) (max brightness or min brightness) - (average brightness) note 3. measuring point note 9. the lcd driving voltage should be adjusted so as to obtain maximum contrast. note 10. the color temperature of light source is 5200k. 88 44 132 110 165 55 (pixel) (1) (176) (1) (220) p1 p2 p3 p4 p5 p6 p7 p9 p8 note 7. definition of viewing angle f1 and f2 f f=0 deg sensor sensor : bm-5 or similar equipment 2.0 f1 f2 f1<0 deg hitachi displays, ltd. sh. no. page date mar . 16, 2004 7. block diagram led an ca1 led ca2 led ca3 g1 g220 hd66772 gnd vcc reset tft-lcd 176(h) x rgb x 220(v) hd66774s dotclk, vsync enable, hsync vcom cl1, flm, disptm, m, eq dcclk, gcs*, gda, gcl 9 vcom vreg1out ddvdh vdh ddvdh pd17-pd0 id, scl, vld sdo, sdi, cs* reset reset cl1, flm, disptm, m, eq dcclk, gcs*, gda, gcl 18 6 4 x176,y220 x1,y220 x1,y1 vci note 1 connect the resistor for overcurrent protection between ca(cathode) and gnd. r1-3: 100 ohm r1 r2 r3 note 1 3284ps 2607-TX06D15VM1EAA-4 7 -1/1 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 8. 1 internal pin connection 8. interface i/f: suitable connector jae:ff0245sa1 (jae:ff0245ss1) 3284ps 2608-TX06D15VM1EAA-4 8 -1/9 pin no. signal function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 41 42 43 44 45 an ca1 ca2 ca3 gnd for led1 power supply for led gnd for led2 gnd for led3 reset reset nc nc nc nc nc nc nc sdo serial instruction data out sdi serial instruction data in scl nc cs* chip select vld vsync vertical synchronous for display data hsync horizontal synchronous for display data dotclk clock signal for display data enable enable signal for display data pd17 pd16 pd15 pd14 pd13 display data(r5) display data(r4) display data(r3) display data(r2) display data(r1) pd12 pd11 pd10 pd9 pd7 pd6 pd5 pd4 pd3 pd2 pd1 display data(g5) pd8 display data(g4) display data(g3) display data(g2) display data(g1) display data(g0) display data(b5) display data(b4) display data(b3) display data(b2) display data(b1) pd0 39 vci power supply for analog vcc power supply for logic gnd gnd agnd id nc nc nc nc nc nc nc nc display data(r0) display data(b0) gnd for analog active data signal for write operation id synchronous clock signal www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 3284ps 2608-TX06D15VM1EAA-4 8 -2/9 8.2 rgb interface mode setting rgb interface mode & unused pin connection rgb interface mode colors 18-bit 262k pd17-0 16-bit 65k pd17-13, pd11-1 pd12, pd0 signal 29 41 gnd gnd when the 16-bit rgb-i/f is selected, pd12 and pd0 pins must be fixed to the gnd level. used pins rgb data bus unused pins pin no. pd12 pd0 input data & gram write data pd 0 pd 1 pd 2 pd 3 pd 4 pd 5 pd 6 pd 7 pd 8 pd 9 pd 10 pd 11 pd 12 pd 13 pd 14 pd 15 pd 16 pd 17 data bus (input data) b 0 b 1 b2 b3 b4 b5 g0 g1 g2 g3 g4 g5 r0 r1 r2 r3 r4 r5 gram write data data bus (input data) b 0 b 1 b2 b3 b4 b5 g0 g1 g2 g3 g4 g5 r0 r1 r2 r3 r4 r5 gram write data pd 13 pd 14 pd 15 pd 16 pd 17 pd 1 pd 2 pd 3 pd 4 pd 5 pd 6 pd 7 pd 8 pd 9 pd 10 pd 11 18-bit rgb interface 16-bit rgb interface in 16-bit rgb-i/f, the input data are expanded into 18-bit by adding one bit (the same data as the msb of rb) to the lsb of rb data within hd66772. 32 64 32 64 64 64 b g r number of color number of grayscale rgb-i/f mode 16-bit 18-bit 65,536 262,144 number of color www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 8.3 gram address map 215 4 216 217 6 5 g1 1 3 2 "0200"h x 1 2 3 4 173 174 175 176 y 218 219 220 g2 g3 g4 g5 g6 g215 g216 g217 g218 g219 g220 ss=1,gs=0 "0201"h "0202"h "0203"h "02ac"h "02ad"h "02ae"h "02af"h "0300"h "0301"h "0302"h "0303"h "03ac"h "03ad"h "03ae"h "03af"h "0400"h "0401"h "0402"h "0403"h "04ac"h "04ad"h "04ae"h "04af"h "0500"h "0501"h "0502"h "0503"h "05ac"h "05ad"h "05ae"h "05af"h "0000"h "0001"h "0002"h "0003"h "00ac"h "00ad"h "00ae"h "00af"h "0100"h "0101"h "0102"h "0103"h "01ac"h "01ad"h "01ae"h "01af"h "d600"h "d801"h "d802"h "d803"h "d8ac"h "d8ad"h "d8ae"h "d8af"h "d700"h "d901"h "d902"h "d903"h "d9ac"h "d9ad"h "d9ae"h "d9af"h "d800"h "da01"h "da02"h "da03"h "daac"h "daad"h "daae"h "daaf"h "d900"h "db01"h "db02"h "db03"h "dbac"h "dbad"h "dbae"h "dbaf"h "da00"h "d601"h "d602"h "d603"h "d6ac"h "d6ad"h "d6ae"h "d6af"h "db00"h "d701"h "d702"h "d703"h "d7ac"h "d7ad"h "d7ae"h "d7af"h 3284ps 2608-TX06D15VM1EAA-4 8 -3/9 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 8.4 interface timing item symbol unit min typ max tscyc us 0.1 - 20 write read serial clock cycle time tsch ns 40 - - write read serial clock "high" level pulse width tscl ns 40 - - write read 0.35 - 20 150 - - 150 - - - - 20 tscr, tscf ns serial clock rise / fall time 20 - - tcsu ns chip select set up time 60 - - tch ns chip select hold time 30 - - tsisu ns serial input data set up time 30 - - tsih ns serial input data hold time - - 130 tsod ns serial output data delay time 5 - - tsoh ns serial output data hold time serial clock "low" level pulse width clock synchronized serial interface timing characteristics item symbol unit min typ max 0 - 1 vsync/hsync set up time 20 - - ns 40 - - 10 - - - - - ns 100 - - ns 10 - - ns 40 - - ns - 25 ns - ns ns tsyncs clock enable set up time tens ns 10 enable hold time vld set up time vld hold time dotclk "low" level pulse width dotclk "high" level pulse width dotclk cycle time data set up time data hold time dotclk,vsync,hsync rise/fall time tenh tvls tvlh pw dl pw dh tcycd tpds tpdh trgbr,trgbf ns 40 40 - - - rgb interface timing characteristics <<18/16bit rgb interface mode(hwm=1)>> item symbol unit min typ max reset timing characteristics 1 - - tres ms reset "low" level width - - 10 trres us reset rise time 3284ps 2608-TX06D15VM1EAA-4 8 -4/9 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 reset timing vil reset* vil tres vih trres rgb interface timing vih vih vil vil trgbf trgbr vsync hsync vih vil vih vil vih vil vih vil vih vil vih vil vih vil vih vil enable vld vih vil vih vil vih vil vih vil vih vil vih vil vih vil dotclk pd17-0 tsyncs tens tenh tvls tvlh pw dl pw dh trgbf trgbf tcycd tpds tpdh wright data clock synchronized serial interface timing vih vil vih vil input data vil scl vil cs* vih vil vih vih vih vil vil input data tcsu tscr tsch tscl tch tscyc tsisu tsih voh1 vol1 output data output data voh1 vol1 tsod tsoh sdi sdo start : s end : p vil vih tscf 3284ps 2608-TX06D15VM1EAA-4 8 -5/9 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 16-/18-bit rgb interface timing fpp : front porch period bpp : back porch period dp : display operation period vlw : the period in which vsync is low level hlw : the period in which hsync is low level bpp v = 8h 1 frame 1h vsync hsync dotclk enable vld 1clk vlw=4h hlw=4clk fpp v = 8h hsync pd17-0 1h bpp h =8clk fpp h =4clk valid data (176) dp=220h f dotclk = f flm x (220 + bpp v + fpp v ) x (176 + bpp h + fpp h ) bpp h fpp h bpp v fpp v dp the number of raster-rows of 1frame min typ max 2h 14h 2h 14h vlw hlw 1dotclk 1h 220h 240h bpp v + dp + fpp v 8h 8h 4h 4dotclk 4dotclk - - - - - bpp v + fpp v = 16h - n ote - - - item hlw (1dotclk) 2hlw (8dotclk) bpp h > hlw hlw > 1dotclk vlw > 1h 3284ps 2608-TX06D15VM1EAA-4 8 -6/9 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 8.5 register setting flow < power on sequence > graphic ram writing (rgb i/f) r07h 0x0001 wait 2 frames or more r0ch r07h 0x0000 0x0032 r07h 0x0022 wait 2 frames or more r07h r0ah r10h r0ah 0x0000 0x0100 0x0000 0x0100 serial transfer < display off sequence > < display on sequence > serial transfer serial transfer power supply setting(1) r11h r12h r13h r14h r0ah r0ah r0ah index value 0x1010 0x0000 0x0609 0x2d0f 0x0100 0x0101 0x0102 serial transfer serial transfer serial transfer power supply setting(2) power supply setting(3) mode setting wait 20ms or more r10h r0ah 0x0808 0x0100 r13h r0ah 0x0619 0x0101 r01h r02h r03h r04h r05h r08h r0bh r23h r24h r40h r41h r42h r43h r44h r45h r30h r31h r32h r33h r34h r35h r36h r37h r3fh r0ah r0ah 0x011b 0x0500 0x1230 0x0000 0x0000 0x0808 0x0000 0x0000 0x0000 0x0000 0x0000 0xdb00 0xefef 0xaf00 0xdb00 0x0100 0x0707 0x0102 0x0204 0x0506 0x0000 0x0706 0x0402 0x0003 0x0106 0x0107 hight-speed write mode r0ch r21h r22h (note 1) 0x0000 ----- wait 20ms or more serial transfer note 1 rgb i/f mode 16bit 18bit value 0x0111 0x0110 r07h 0x0033 wait 2 frames or more r07h r0ah r07h 0x0021 0x0100 0x0023 wait 2 frames or more r0ch r21h r22h rgb i/f mode 0x0000 0x0000 ----- graphic ram writing (spi) internal clock operation mode clock operation internal mode operation mode note 2 to : display on sequence 100ms more than (note 2) operation amplifier stabilizing period 3284ps 2608-TX06D15VM1EAA-4 8 -7/9 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 (standby) (sleep) display off sequence standby setting(stb="1") display on sequence power on sequence standby canceled(stb="0") wait 10ms oscillation start standby setting standby canceled sleep setting(slp="1") sleep canceled(slp="0") sleep setting sleep canceled display off sequence serial transfer serial transfer display on sequence power on sequence < standby & sleep sequence > 3284ps 2608-TX06D15VM1EAA-4 8 -8/9 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 display off gon="1" , dte="1" , d1-0="10" display off gon="1" , dte="0" , d1-0="10" wait 2 frame or more display off gon="0" , dte="0" , d1-0="00" wait 2 frame or more ram setting cl="1" wait 40ms or more display on gon="0" , dte="0" , d1-0="01" wait 2 frame or more display on gon="1" , dte="0" , d1-0="01" display on gon="1" , dte="0" , d1-0="11" wait 2h period or more display on gon="1" , dte="1" , d1-0="11" display off gon="1" , dte="1" , d1-0="10" display off gon="1" , dte="0" , d1-0="10" wait 2 frame or more display off gon="0" , dte="0" , d1-0="00" wait 2 frame or more ram setting cl="0" wait 40ms or more display on gon="0" , dte="0" , d1-0="01" wait 2 frame or more display on gon="1" , dte="0" , d1-0="01" display on gon="1" , dte="0" , d1-0="11" wait 2h period or more display on gon="1" , dte="1" , d1-0="11" serial transfer serial transfer 8 colors mode serial transfer serial transfer normal mode (normal mode 8 colors mode) (8 colors mode normal mode) < 8 colors mode setting > 3284ps 2608-TX06D15VM1EAA-4 8 -9/9 www.datasheet.co.kr datasheet pdf - http://www..net/
www.datasheet.co.kr datasheet pdf - http://www..net/
www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 10. visual inspection 10.1 inspection condition 1) ambient illumination : 1000 - 1500 [lx] 2) distance between eyes of an inspector and the lcd module : approximately 20 [cm] 3) viewing angle : < 30deg 30deg eye eye lcd mold 10.2 definition of zone the visual inspection zone of a lcd module is divided into three. a zone : the inside of the active area. b zone : the outer periphery of the active area. c zone : whole of the lcd module except the zone a and b. (including fpc & plastic mold) active area viewing area a zone b zone c zone 30deg 1.3mm 1.3mm whole of the lcd module except the zone a and b 3284ps 2610-TX06D15VM1EAA-4 10-1/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 10.3 cosmetic specification no. item maximum acceptable number unit applied zone inspection mode remarks 1 dot defect sparkle mode 1 dot adjacent dots black mode 1 dot adjacent dots the total number 2 line defects uneven brightness: line shape 3 4 uneven brightness: dot shape stain inclusion : line shape [mm] width, length stain inclusion : dot shape [mm] diverge diameter uneven anti reflection scratch, dent of plastic mold scratch of fpc w < 0.01 0.01 < w < 0.05 0.05 < w d < 0.1 0.1 < d < 0.2 0.2 < d c c a a a a a a,b a,b a,b a a light-on light-on light-on light-on light-off light-on light-off light-off light-off light-off pcs pcs pcs pcs pcs 5 6 7 8 9 l:ignored l < 2.0 l > 2.0 0 unit unit none ignored ignore see dot shape by limited sample by limited sample 0 0 0 0 2 2 2 2 serious one is not allowed serious one is not allowed 1),2),4) 6) 5),6),7) 5),6),7) 6) 6) 6) note: 1) defect whose area per each dot is over 50 % is regarded as dot defect. 2) defect whose brightness at all black screen is more than 30% is regarded as bright dot defect. 3) defect whose brightness at all white screen is less than 70% is regarded as dark dot defect. 4) defect dots which are not adjacent are regarded as single dot defect each. 5) defect which can be easily wiped off is disregarded 6) in case any problems would be brought out, both parties should discuss needed items such as limited samples. 7) in case of gray scale pattern, obvious defect is to be rejected. l definition of w and l b definition of d d = a + b 2 (mm) 3284ps 2610-TX06D15VM1EAA-4 10-2/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 no. 10 y x y x y l l= 1.8 [mm] y < (1/4)xl item glass crack criteria (1) electrode (2) generality (3) corner (4) the crack that has potential to enlarge none x < 1.5 y < 1.5 * no crack allowed to reach seal area. y < 1, in case of two cracks found. x < 5.0 [mm] y < 1.5 [mm] * no crack allowed to reach seal area. y < 1, in case of two cracks found. a b c 3284ps 2610-TX06D15VM1EAA-4 10-3/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 11. precaution in design 11. 1 general attention (1) the lcd module is designed as display for mobile phone. when it is used for other purposes, we do not guarantee these specifications at all about the contents, quality, safety etc.. moreover, this module is not particularly developed as an object for equipment in connection with a human life such as medical apparatus of life support relation. (2) please do not decompose this lcd module. there is danger such as a burn, electric shock, and an injury. moreover, when module is decomposed, we do not guarantee these specifications at all about the contents, quality, safety etc.. 11.3 handling precautions (1) please do not leave on a humid environment for a long time. in storage, when the ambient temperature is over 35 degrees c , please avoid high humidity. the polarizers degradation is easily caused in high temperature and high humidity. moreover, it is also the cause of bubble and peeling of polarizer. please store/operate the lcd module within the relative temperature and normal humidity. (2) since the polarizer on the top tend to be easily scratched, they should be handled with full care so as not to get them touched, pushed or rubbed by a piece on glass, tweezers and anything else which are harder than a pencil lead 3h. (3) maximum pressure to the surface must be less than 1.96pa . and if the pressure area is less than 1cm 2 , maximum pressure must be less than 1.96n . (4) as th e adhesives used for adhering upper/lower polarizers which will be deteriorated by a chemical reaction with such chemicals as acetone, toluene, hexane, ethanol and isopropyl alcohol. don't let the organic solvent or chemicals adhere to polarizers. (5) lightly wipe to clean the dirty surface with absorbent cotton or other soft material like chamois, soaked in the recommended chemicals without scrubbing it hardly. always wipe the surface horizontally or vertically. never give a wipe in a circle. to prevent the display surface from damage and keep the appearance in good state, it is sufficient, in general, to wipe it with absorbent cotton. 11.2 precautions against electrostatic discharge as this module contains c-mos lsis, it is not strong against electrostatic discharge. make certain that the operator's body is connected to the ground through a list band etc. and don't touch i/f pins directly. 3284ps 2611-TX06D15VM1EAA-4 11-1/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 (6) immediately wipe off saliva or water drop attached on the display area because it may cause deformation or faded color. (7) fogy dew deposited on the surface may cause a damage, stain or dirt to the polarizer. when you need to take out the lcd module from some place at low temperature for test, etc. it is required to be warmed them up to be temperature higher than room temperature before taking them out. (8) touching the display area or i/f pins with bare hands or contaminating them are prohibited, because the stain on the display area and poor insulation between terminals are often caused by being touched with bare hands. (some cosmetics are detrimental to polarizers.) (9) in general, the glass is fragile so that it, especially on its periphery, tends to be cracked or chipped in handling. please do not give the lcd module sharp shocks caused by falling etc. (10) the lcd is a product made from glass. it is possible to be damaged by the strong shock. please be careful and prevent to drop it. (11) it doesn't bend and scratch the i/f part. these are cause of no good contact. please be careful. 11.4 operation precaution (1) the spike noise causes the mis-operation of circuits. recommended condition of spike noise level is as follows : vcc=+/-200mv(over and under shoot voltage) (2) response time depends on the temperature. (in lower temperature, it becomes longer). and also brightness and color depend on the temperature. (3) be careful for condensation at sudden temperature change. condensation make damage to polarizer or electrical contact part. and after fading condensation, smear or spot will occur. (4) when fixed patterns are displayed at long times, afterimage is likely to occur. (5) module has high frequency circuit. if you need to shield the electromagnetic noise, please do in yours. (6) do not connect or remove the module from main system with power applied. (7) strong light exposure causes mis-operation of driver. 3284ps 2611-TX06D15VM1EAA-4 11-2/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 11.5 storage when storing lcd module as spare parts for a long time, the following precautions are necessary. (1) store the lcd modules in a dark place ; do not expose them to sunlight or fluorescent light. keep the temperature between 10 degrees c and 30 degrees c,and the humidity between 55% and 75%. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. 11.6 safety (1) this liquid crystal display module is using glass. when it damages, please wear a protection glove to deal it. moreover, when any liquid leaked out of a damaged glass cell comes in contact with your hands, please wash it off well with soap and water. (2) solder is used for mounting of internal electronic component at print circuit board. since the lead(pb) is contained in solder. when you want to discard this lcd module, please follow local ordinances or regulations for disposal. 3284ps 2611-TX06D15VM1EAA-4 11-3/3 www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 12.1 lot mark the lot mark consists of 7 or 10-digit production control number. 12. designation of lot mark year figure in lot mark 2005 2006 6 5 month figure in lot mark jan. 1 month figure in lot mark feb. 2 mar. 3 apr. 4 may 5 june 6 july 7 aug. 8 sep. 9 oct. a nov. b dec. c a 3 a day year revision 2 h production base location of the lot mark : on the back of the lcd module printing method of a lot mark : laser marker or inkjet printer t x 0 6 d 1 5 v part name month * * production control day figure in lot mark 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 7 8 9 day figure in lot mark 11 12 13 14 15 16 a b c d e f 17 18 19 g h j day figure in lot mark 21 22 23 24 25 26 k l m n p q 27 28 29 r s t day figure in lot mark 30 31 w x 10 20 u v m 1 e a a 2003 2004 4 3 production base made in japan made in china h s figure in lot mark revision contents of change a 3284ps 2612-TX06D15VM1EAA-4 12-1/1 w (note 1) - serial no. lower 3-digit lot no. upper 7-digit lot no. production control no. printing method inkjet printer laser marker note (1) www.datasheet.co.kr datasheet pdf - http://www..net/
hitachi displays, ltd. sh. no. page date mar . 16, 2004 13. precaution for use (1) a limit sample should be provided by the both parities on an occasion when the both parties agree to its necessity. judgment by a limit sample shall take effect after the limit sample has been established and confirmed by the both parties. (2) on the following occasions, the handling of the problem should be decided through discussion and agreement between responsible persons of the both parties. (1) when a question is arisen in the specifications. (2) when a new problem is arisen which is not specified in the specifications. (3) when an inspection specification change or operating condition change by customer is reported to hitachi, and some problem is arisen in the specification due to the change. (4) when a new problem is arisen at the customer's operating set for sample evaluation (3) regarding the treatment for maintenance and repairing, both parties will discuss it in six month later after latest delivery of this product. the precaution that should be observed when handling lcm have been explained above. if any points are unclear or if you have any requests, please contact hitachi. 3284ps 2613-TX06D15VM1EAA-4 13-1/1 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of TX06D15VM1EAA

	To Download TX06D15VM1EAA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .